Quick Links. For Continental Europe. For Australia and N. For Continental Europe and.

Author:Akirg Kajit
Language:English (Spanish)
Published (Last):2 December 2014
PDF File Size:18.92 Mb
ePub File Size:17.47 Mb
Price:Free* [*Free Regsitration Required]

S ilver Type K B lack Type. All rights reserved. Unauthorized copying and distribution is a violation of law. When servicing, observe the original lead dress.

If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.

After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading should be between 1M and 5.

When the exposed metal does not have a return path to the chassis, the reading must be. Connect a 1. Check each exposed metallic part, and measure the voltage at each point. Reverse the AC plug in the AC outlet and repeat each of the above measuremen ts.

The potential at any point should not exceed 0. In case a measuremen t is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer. Examples of typical ES devices are integrated circuits and some field-effect transistor- sand semiconductor "chip" components.

The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge ESD. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.

After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

Use only a grounded-tip soldering iron to solder or unsolder ES devices. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static ESD protected " can generate electrical charge sufficient to damage ES devices. Do not use freon-propell ed chemicals. These can generate electrical charges sufficient to damage ES devices.

Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.

Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Caution Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. Minimize bodily motions when handling unpackaged replacement ES devices. Otherwise hamless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.

Distinction of PbF P. Caution: Pb free solder has a higher melting point than standard solder; Typically the melting point is 50 - 70F 30 - 40C higher. Please use a high temperature soldering iron. In case of the soldering iron with temperature control, please set it to 20F 10C. When soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure to heat the soldering points with the Pb free solder until it melts enough. Turn off the power and pull out AC cord.

Remove the Top Case. Remove the Front Panel. Take out the disc and put the Opener Roller on fully position for direction of Arrow. FL Display:. Press [4] [2] keys of remote controller. Please make it reference as an example of a display. Self-Diagnosis Function provides information for errors to service personnel by Self-Diagno sis Display when any error has occurred. You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode.

Error Code Diagnosis contents U30 Remote control code error. Description Monitor Display Display appears when main unit and remote No display controller codes are not matched.

The power is turned off forcibly. For 30 minutes after this, all key entries are disabled. Fan motor operates at the highest speed for the first 5 minutes. For the remaining 25 minutes, fan motor is also stopped. The event is saved in memory as well. Displayed when communication error has No display occurred between Main microprocessor and Timer microprocessor. Initial setting for error code in memory Error code Initialization is possible with error code initialization and main unit initialization.

F58 Drive hardware error When drive unit error is detected, the event is saved in memory. F34 Initialization error when main When initialization error is detected after microprocessor is started up starting up main microprocessor for program for program recording recording, the power is turned off automatically.

The event is saved in memory. Since the power cord fell out during a power No display failure or operation, it is under restoration operation. If a display does not disappear, there is the possibility that defective Digital P. No display. Display for 5 seconds. Cannot read. Please check the disc.

Description Monitor Display Unit is in termination process now. No display BYE is displayed and power will be turned off. Setting every kind of modes for servicing. Service Mode. Removing a disc that cannot be ejected. The display The tray will open and unit will shift to P-off leaves.

While Demonstration Lock is being set, this Forced disc eject function is not accepted. The display leaves. When the power button is not effective while Display in P-off mode.

Description shown below continually. NOTE2: If the unit has hung-up because of pressing keys for over 10 seconds, once turn off the power, and reexecute this command. Ejection of the disc is prohibited. The lock setting is effective until unlocking the tray and not released by Main unit initialization of service mode. LOCK is displayed for 3 seconds. SelfDiagnosis Functions. Output from AV Decoder. Press [1] [4] in White Picture Output mode. Press [1] [2] in service mode.

Switch Interlace and Progressive in EE mode. Press [2] [4] in Audio Pattern Output mode. Press [4] [1] in service mode. Delete the Laser Used Laser used time stored in the memory of the Time unit is deleted. Press [4] [2] in service mode. RAM Drive error code display. Service Explorer. Time when the error has occurred is displayed for 5 seconds. Key operation Remote controller key Press [5] [1] in service mode.

Press [5] [2] in service mode. Production Date Display Display the date when the unit was produced. Last Drive Error, Error history and Error Codes stored on the unit are initialized to factory setting. Disassembly Flow Chart The following chart is the procedure for disassemblin g the casing and inside parts for internal inspection when carrying out the servicing. To assemble the unit, reverse the steps shown in the chart below. Slide Top Case rearward and open the both ends at rear side of the Top Case a little and lift the Top Case in the direction of the arrows.


Panasonic DIGA DMR-ES10 user manual

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. If you want to quickly view the content of pages found on the following pages of the manual, you can use them. For optimum performance In Canada: and safety, please read these instructions carefully. Before connecting, operating or adjusting this product, please read For U. The warranty can be found on page Connection with a television and video cassette recorder The connection will allow the video cassette recorder to be used for playback when this unit is turned off.


Panasonic Diga DMR-ES10 Operating Instructions Manual


Related Articles